For service please call
1-800-837-2503 or
Request Service Here

Reduce Operator Fatigue and Repetitive Motion Injuries with the B-19-RG

The B-19 RG pairs FlexArm’s smoothest counterbalance arm with an end effector specifically designed for grinding applications.  The only goal in putting together this package was to provide the customer with restriction free weightless movement of the tool.  The package is a simple solution to operator fatigue and possible injury from repetitive motion.

B-19-RG 3D model

 

Click Image for Autodesk 3-D Drawing

 

Click Image for Brochure

 

Click Image for Manual

 

If you are interested in a counterbalancing solution that will reduce operator fatigue and injury, contact us or give us a call at 1-800-837-2503.

One response to “Reduce Operator Fatigue and Repetitive Motion Injuries with the B-19-RG”

  1. BRIAN BURNS says:
    October 28, 2021 at 9:42 am

    Good Morning!
    Can you please send me all the literature you have on your B-19-RG for an electric angle grinder?

    Reply

Leave a Reply

Your email address will not be published. Required fields are marked *

Related Topics

Standard Features

  • Hand Pendant
  • 22″ Touch Screen Monitor
  • Omron FlexCNC Controller
  • Mobile Control Panel
  • Through Spindle Coolant 
  • Auto Tool Changer 
  • Flood Coolant
HP
Max RPM
FT/LBS
Series

18

4000

92

C-20-02 / C-10-02

18

6000

61

C-20-02 / C-10-02

33

12000

61

CM-20-02

Auto Stand-Off – This is currently defined to be surface stand-off and not to be confused with vector stand-off in 5-axis mode. The current auto stand-off is based on a changing surface and will adjust vertically based on the angle of the “A” Axis, so there is five (5) axis taken into account during the calculations, but this is not the same as the tool vector stand-off. There is the ability to do the vector stand-off change while the machine is running manually with buttons on the screen.

Z-Reader Probe – The Z-Reader is a device for mapping the location of the surface. It can be controlled manually & programmatically. The option is NOT active while cutting & is retracted out of harm’s way. It can be triggered to verify the surface at every pierce before the cutting process starts, or it could be used to drive surface mapping of the whole part before cutting starts. It begins with initialization or zeroing of the device to the surface at the beginning of a program and then accumulates or tracks the difference from that zeroing effort.

Automatic Edge Finder – The edge finder is or can be utilized manually (Jogging Method & Screen Buttons), programmatically (M & G codes), or fully automatic routine (dedicated program). This option sets offsets & program rotation to match the orientation & location on the cutting table.

AC Unit Installed on Electrical Cabinet – The unit is mounted on the cabinet’s High Power (480v) side. It is close to the location where the drives are mounted. This option keeps the cabinet temperature stable and allows heat dissipation faster. The servo drives for all axes are the most significant contributors to heat inside the electrical cabinet.

5-Axis Renishaw Calibration – The calibration unit is a Renishaw model APCA45 with a modified spherical stylus. The device has a retractable cover and air purge to clear debris & dust during the activation process. It mounts to a swing arm controlled by a pneumatic rotary, so it is out of the way during regular operation and swings into the calibration position for calibration only. 

HP
Max RPM
FT/LBS
Series

18

4000

92

G-20-06 / G-10-06

18

6000

61

G-20-06 / -10-06

40

4000

217

GM-20-06 / G-20-06 / G-10-06

40

6000

145

G-20-06 / G-20-06 / G-10-06